Drinkware Sample Request Checklist for B2B Buyers

Drinkware Sample Request Checklist for B2B Buyers

Samples decide projects. A buyer who receives the wrong configuration in week one either restarts the brief or disappears, and both outcomes cost more than the sample itself. This checklist covers what to request, what to test when it arrives, and how to turn the result into a purchase order.

What to ask for before the sample ships

Item Why it matters
Model reference and current revision Prevents approving an older version
Material grade per component SUS304 vs 316, lid and straw material
Finish and colour reference Pantone or RAL, plus gloss level
Decoration method and artwork file Determines what the sample can prove
Lid and straw configuration Lids change insulation and leak behaviour
Packaging option Colour box or poly bag changes carton size

If the sample arrives without this information, you cannot tell whether a failure is a design problem or a brief problem.

Three sample types, three different questions

  • Stock sample — proves the model exists and shows the standard finish. Fastest, and usually free or freight-only
  • Branded sample — proves decoration quality on your artwork. This is the sample that decides the logo method
  • Pre-production sample — proves the exact production configuration, including packing. Required before a large order

Plan for the branded sample if decoration matters, and the pre-production sample if the order is above 3,000 pieces.

What to test when it arrives

  1. Leak, on its side and upside down — 30 minutes each, with a paper towel underneath
  2. Insulation — 95°C water, measure at 1 h, 3 h and 6 h; record ambient temperature
  3. Lid cycle — open and close 50 times by hand; a hinge that loosens early fails at 500
  4. Drop — 1.2–1.5 m onto tile on all six faces
  5. Decoration — fingernail scratch at the edge, then a dishwasher cycle if claimed
  6. Fit — base diameter against the target cup holder if it is a vehicle product

Write the results down. A sample approved from memory cannot be defended when the bulk lot differs.

The sample approval form

A one-page approval form prevents most disputes later. It should record: sample type, date received, model and revision, grade offered, measured capacity, decoration method, test results, decision (approved / approved with changes / rejected), and the signature of the person who approved it.

Send the signed form back to the supplier. It becomes the reference document for the production order.

Timing and cost expectations

  • Sampling lead time: 5–7 days from an approved brief, plus courier time
  • Cost: stock samples are typically free with freight paid by the buyer; branded samples usually carry a charge, often credited against the bulk order
  • Revisions: allow one round. A second round usually means the brief was unclear rather than the sample being wrong

How many samples to request

For a first project, request two units of the target model and one of an alternative. Two units let you keep one as a reference and test the other destructively; the alternative shows whether the supplier's second option is better suited to your market.

For a repeat order, one pre-production sample is enough if nothing changed. If the finish, lid or packaging changed, treat it as a new project.

Red flags in a received sample

  • Different lid or capacity than the one quoted
  • Another brand's logo still visible under the coating
  • Decoration that can be scratched off with a fingernail
  • A sample shipped without any documentation
  • Carton dimensions that do not match the stated packing list

Each of these points to a longer supply chain than the supplier described, or to a brief that was not read.

Who pays for what

Common practice, and worth confirming in writing:

Item Typical arrangement
Stock sample Free, buyer pays courier
Branded sample Charged, often credited against the bulk order
Sample courier Buyer's account or prepaid
Tooling sample (new mould) Charged; rarely credited

Sample versus production: what can still differ

Even an approved sample does not guarantee identical bulk. Three variables commonly shift between the sample and the production lot:

  • Colour batch — powder coat is mixed per lot; ask for the approved colour reference to travel with the order
  • Decoration position — a hand-placed sample logo can sit 2–3 mm differently from a jig-set production run; specify the tolerance
  • Lid supplier — if the lid comes from a third party, the sample lid and the production lid may be different batches

The defence is a pre-production sample plus an inspection that checks these three items against the approved reference.

Five mistakes that waste a sample round

  1. Approving a logo on a different finish than the production order
  2. Testing leakage upright only
  3. Not recording the starting water temperature
  4. Ignoring carton and packaging in the sample decision
  5. Approving verbally, so nobody can prove what was agreed

From sample to order

Once the sample is approved, the purchase order should restate the configuration it represents: grade, finish, decoration, packing, inspection standard and delivery term. Anything not written down reverts to the supplier's default.

Start with our RFQ checklist, compare candidates with the sample comparison method, then send the brief through the inquiry form. Browse the catalog to choose a model reference.

Last updated: November 2026.

Terug naar blog