SUS304 vs SUS316 Stainless Steel for Custom Drinkware: A B2B Buyer Guide
Share
Grade selection is one of the few decisions in a drinkware project that changes cost, performance and compliance at the same time — and it is usually made in a single line of an email. This guide explains what actually differs between SUS304 and SUS316, when the upgrade is justified, and how to verify what you received.
What the two grades actually contain
| Element | SUS304 (18/8) | SUS316 (18/10) | Effect |
|---|---|---|---|
| Chromium | 18–20% | 16–18% | Forms the passive oxide layer |
| Nickel | 8–10.5% | 10–14% | Stability, formability, finish quality |
| Molybdenum | — | 2–3% | Resistance to chlorides (salt) |
| Carbon | ≤0.08% | ≤0.08% | Weldability |
The shorthand “18/8” and “18/10” refers to chromium and nickel percentages. The number most buyers never hear is molybdenum — and it is the only element that meaningfully changes behaviour in salt-heavy or acidic use.
Corrosion: what molybdenum changes
A useful single number is the pitting resistance equivalent number (PREN), approximated as Cr + 3.3 × Mo + 16 × N. SUS304 lands around 18–20; SUS316 around 24–26. That gap is why 316 survives coastal air, road salt and chloride-rich detergents that slowly pit 304.
In practice, the failure markers to look for on a sample are:
- Brown tea-coloured staining at welds after dishwasher cycles
- Pitting — small dark craters, usually at the bottom weld or the lid thread
- Rust bleed at the seam where the outer shell meets the base
Ask for a salt-spray result at 48, 96 and 120 hours on the finished, coated article — not on raw steel sheet. Coating defects decide the outcome more often than the grade does.
Food contact: the documents that matter
Grade is a material property; food-contact compliance is a test result on a specific article. For export programmes the usual pair is:
| Market | Test | What it covers |
|---|---|---|
| United States | FDA 21 CFR 175.300 | Food-contact coating/extraction on the submitted sample |
| European Union | LFGB | Migration testing for the submitted sample and medium |
| Both | RoHS | Restricted substances in listed models — not food contact |
Two things buyers get wrong here. First, a report names one sample; a different colour, coating or capacity is not automatically covered. Second, migration results depend on the beverage, temperature and duration tested — an acidic drink result cannot be borrowed for a coffee flask.
When SUS304 is the right answer
- Standard water bottles, tumblers and food jars sold in inland markets
- Programmes where the unit price is the deciding factor
- Products with a full internal coating or liner that isolates the beverage
For the large majority of B2B drinkware orders, 304 with a properly applied interior finish performs well for years. Upgrading without a reason mostly moves cost, not quality.
When SUS316 is worth the premium
- Coastal or marine markets — salt air and salt water exposure
- Sports and outdoor programmes used with electrolyte drinks
- Kids drinkware where parents read the spec sheet
- Premium retail where “316” is a legitimate selling point on the box
- Long-life institutional buyers (hotels, gyms, cruise lines)
The premium is usually in the range of 8–15% on the body material, which translates to a smaller number on the finished unit. Whether that is worth it depends on the claim you intend to make in the market.
Watch for grade substitution
Cheaper grades — SUS201, SUS430, or “304-equivalent” — appear in quotations that look 20% below the market. They are not fraud by default; they are simply a different material. The risk is when a quotation says 304 and the goods are not.
Three checks that cost little:
- XRF spot check on a random unit at inspection — a handheld analyser reads Cr/Ni/Mo in seconds
- Mill certificate for the coil lot, matched to the production dates
- Independent lab test on one unit per order for high-value programmes
Agree in the purchase order which of these will happen, and who pays for a failed result.
How to write the specification line
A specification that cannot be misread looks like this:
Body, inner wall: SUS304, 0.4 mm. Outer wall: SUS304, 0.4 mm. Interior finish: electrolytic polish. Exterior: powder coat, RAL 9010. Salt spray: 96 h, no pitting. Food contact: FDA 21 CFR 175.300 report for this finish. Third-party XRF verification at pre-shipment.
Seven data points. Any supplier who cannot confirm all seven is guessing.
Where corrosion failures actually start
In field returns, pitting rarely starts on a smooth wall. It starts at four places:
| Location | Cause | Prevention |
|---|---|---|
| Bottom weld | Heat-affected zone loses chromium locally | Post-weld passivation or electropolish |
| Lid thread | Detergent trapped between threads | Thread geometry, rinse-friendly design |
| Rim / lip | Coating edge left exposed | Coating coverage spec, edge inspection |
| Base seam | Water sits in the seam after washing | Seam sealing, drainage geometry |
This matters when you compare quotes: two suppliers can both state “SUS304” and deliver very different corrosion outcomes, because passivation, coating coverage and weld finishing are not in that three-word specification.
Sizing the cost of the upgrade
Material cost is quoted per kilogram, and 316 typically runs 30–50% above 304 on the coil. A 500 ml double-wall bottle uses roughly 0.35–0.45 kg of steel, so the raw-material delta is often small in absolute terms, then amplified by the finished-unit margin structure.
A practical way to decide:
- Estimate the landed unit cost difference for your quantity
- Multiply by the number of units you expect to sell in 12 months
- Ask whether the 316 claim will recover that number in price positioning or in reduced returns
If the answer is “we are not sure”, the correct decision is usually 304 for the first order and 316 for the premium line once the channel is proven.
Frequently asked questions
Is SUS316 twice as good as SUS304?
No. It is measurably better against chlorides and marginally better in acidic food contact, but the difference is invisible in normal inland use. Pay for 316 when the market or the claim requires it.
Does a higher grade improve insulation?
No. Insulation performance comes from the vacuum between the walls and the wall thickness, not from the alloy. A 316 bottle with a poor vacuum seal underperforms a well-made 304 bottle.
Can I mix grades in one product?
Yes and it is common: 304 inner wall with a 201 outer shell is a legitimate cost optimisation, provided the quotation states it and the marketing copy does not claim “all 316”.
What does “food-grade stainless steel” mean?
It is a marketing phrase, not a standard. Ask for the grade and the test report instead.
Materials for a specific model are confirmed in the written quotation. For the wider manufacturing picture, see the factory tour; to compare models, browse water bottles and tumblers; to start a project, send the brief. The RFQ checklist lists everything a quotation needs.
Last updated: November 2026.
Continue reading: buyer guides