Powder Coating vs Laser Engraving vs Sublimation: A Cost and Durability Guide
Decoratie vergeleken: kosten en duurzaamheid
Vijf methoden, vijf uitkomsten: laser, zeefdruk, tampondruk, UV en sublimatie verschillen in kleur, ondergrond en duurzaamheid. De gids laat zien welke methode wint bij 200 en bij 5.000 stuks, waarom goedkeuren op de definitieve afwerking beslissend is en welke vier tests de duurzaamheid voorspellen.
Het volledige artikel is beschikbaar in het Engels.
Share
Decoration decides what the buyer sees first and what the after-sales team hears about six months later. This guide compares the five methods used on stainless drinkware on the three things that actually matter: what the mark looks like, how long it survives, and what it costs at your quantity.
The five methods at a glance
| Method | Colours | Durability | Best substrate | Setup |
|---|---|---|---|---|
| Laser engraving | 1 (material tone) | Excellent | Powder-coated, bare steel | None |
| Silk screen | 1–3 | Good | Flat or gently curved bodies | Low |
| Pad printing | 1–4 | Good | Curved surfaces, small areas | Medium |
| UV printing | Full colour | Medium | Flat panels, complex artwork | High |
| Sublimation | Full colour | Good | Coated blanks only | Medium |
How each method actually behaves
Laser engraving
The laser removes the surface layer or oxidises the steel, so the mark is part of the object rather than on top of it. On powder-coated bodies it produces a high-contrast mark; on brushed steel it is subtle grey; on mirror polish it almost disappears. That difference is why a logo approved on one finish cannot be assumed to work on another.
Silk screen
Ink pushed through a mesh and cured. Excellent for one or two colours on a flat or gently curved surface, and the cheapest route at volume. It struggles on tight curves and on graphics with fine gradients.
Pad printing
A silicone pad transfers ink from a plate to the product, which makes it the standard choice for curved bodies and small marks. Four colours is realistic; beyond that, registration drifts.
UV printing
Full-colour, photographic artwork, cured instantly under UV light. The limitation is adhesion on curved surfaces: the print stretches at the wrap edges, which is where it fails first.
Sublimation
Heat transfers dye into a polymer coating. It only works on coated blanks — on uncoated stainless it simply does not bond. This is the most common misunderstanding in enquiries.
Cost: setup versus per unit
| Method | Setup cost | Per-unit behaviour | Efficient from |
|---|---|---|---|
| Laser | None | Flat, based on machine time | 200 pcs |
| Silk screen | Screen per colour | Falls quickly with volume | 500 pcs |
| Pad print | Plate per colour | Falls with volume | 500 pcs |
| UV | High | Moderate, machine-bound | 1,000 pcs |
| Sublimation | Medium | Low once coated blanks are used | 1,000 pcs |
At 200 pieces, laser usually wins on total cost. At 5,000 pieces with a two-colour logo, silk screen often undercuts it. The crossover point depends on your artwork, not on a general rule.
Testing durability before you commit
- Dishwasher cycles — five cycles, then inspect edges for lifting
- Abrasion — rub with a coin or fingernail at the mark edge
- Tape test — apply and peel adhesive tape over the print
- Chemical wipe — isopropyl alcohol on a cloth, ten passes
Do this on the sample, not on a photo of a sample.
Five mistakes buyers make
- Approving a logo on a bare steel sample, then ordering powder-coated bodies
- Specifying full-colour artwork on a strongly curved surface
- Choosing sublimation without confirming the blank is coated
- Ignoring setup costs when comparing two quotes at low volume
- Not stating the wash claim, then discovering the print fails at 60°C
Artwork requirements by method
| Method | File needed | Typical limitation |
|---|---|---|
| Laser | Vector, single colour, min stroke 0.3 mm | No gradients or halftones |
| Silk screen | Vector, one file per colour, trap 0.1 mm | 3 colours practical maximum |
| Pad print | Vector, per colour | Registration drift above 4 colours |
| UV | Vector or 300 dpi raster, CMYK | Curved surfaces distort at the edges |
| Sublimation | 300 dpi raster, full wrap artwork | Coated blanks only |
Sending a 72 dpi JPEG and asking for a crisp logo is the most common cause of a re-quote.
Lead time impact
Decoration adds time in three places: artwork approval (yours), plate or screen making (1–3 days), and the decoration run itself, which is usually inside the production window rather than after it. Two-colour silk screen on 2,000 pieces typically adds one day; UV on a complex wrap can add three.
Laser engraving is the exception — no setup, so small runs stay fast.
Choosing by market
- Promotional programmes — laser or one-colour silk screen; cost per unit dominates
- Retail gift — sublimation or UV for full-colour presentation
- Premium brand — laser on a textured coat reads as expensive
- Kids — pad print or laser; avoid thin ink films that fail washing
Frequently asked questions
Which method is most durable?
Laser engraving, because the mark is part of the surface. Sublimation and silk screen are close behind when correctly cured.
Can I print a photo on a curved bottle?
Realistically no. UV printing on strong curves stretches at the edges. For photographic artwork, choose a flat panel or a wrap design that tolerates distortion.
Does the finish affect the print?
Yes, decisively. Gloss, matte, textured and gradient coatings all change ink adhesion and the visual result. Approve the print on the actual finish.
Related: surface finishes, comparing samples, and request a quotation.
Last updated: November 2026.
Verder lezen: inkoopgidsen